Antique Engines and Old Iron
[Home] - [HELP] - [Forums] - [Groups] - [Classified Ads] - [Subscribe] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® Shop Equipment Tools and Techniques > Blacksmithing and Metallurgy
Forgot Password? Join Us!

Notices

Blacksmithing and Metallurgy Hand-wrought manufacture of metal objects, extracting metals from their ores, or purifying metals and casting useful items from the metals.

Blacksmithing and Metallurgy

Swage Block


this thread has 5 replies and has been viewed 1068 times

Reply
 
Thread Tools Display Modes
  #1  
Old 03-24-2019, 08:11:29 PM
J.B. Castagnos J.B. Castagnos is offline
Registered
 
Join Date: Nov 2004
Location: South Louisiana USA
Posts: 2,738
Thanks: 931
Thanked 3,593 Times in 1,127 Posts
Default Swage Block

An old friend gave, or willed this 15" swage block to me. He's 92 years old and still makes cypress swings and rockers. The only thing he used it for was to buck the copper tubes he puts through the arms where the chains pass through. I made him a dedicated tool and he let me take it. It's not as rusty as it looks, he had it under his bench grinder, most of it will clean off. Should I just wire brush it, blast it, or pass a flex grinder disc over it?
Attached Thumbnails
Click image for larger version

Name:	swage block.JPG
Views:	363
Size:	137.6 KB
ID:	331297  
Reply With Quote
The Following 4 Users Say Thank You to J.B. Castagnos For This Post:
Sponsored Links
  #2  
Old 03-24-2019, 10:48:27 PM
ulgydog56's Avatar
ulgydog56 ulgydog56 is offline
Registered
 
Join Date: Dec 2017
Location: Smithcreek, Michigan
Posts: 692
Thanks: 99
Thanked 312 Times in 236 Posts
Default Re: Swage Block

it looks like you can do a lot with that block, interesting peace....
Reply With Quote
The Following User Says Thank You to ulgydog56 For This Post:
  #3  
Old 03-25-2019, 07:20:37 AM
Tracy T Tracy T is offline
Subscriber
 
Join Date: May 2009
Location: Cedarbluff, Virginia, USA
Posts: 3,132
Thanks: 996
Thanked 1,733 Times in 980 Posts
Default Re: Swage Block

my grand father had a block kind of like yours, it was for doing stagecoach work. if it were me i would just hit it with a angle grinder with a wire brush and call it done.
Reply With Quote
The Following User Says Thank You to Tracy T For This Post:
  #4  
Old 03-25-2019, 10:49:52 AM
Pete Spaco Pete Spaco is offline
Registered
 
Join Date: Dec 2009
Location: Baldwin, Wisconsin USA
Posts: 976
Thanks: 37
Thanked 713 Times in 362 Posts
Default Re: Swage Block

Depends on what use you will put it to.
If it's just going to be for display, I'd sandblast it and maybe put some kind of anti rust finish on it. Could be LPS 3 or even paint.

But if you are going to use it much, I'd take some time and clean up the swages so they will present a smooth surface when beating metal into them. I'd also sharpen up the edges of the holes some, particularly if you intend to use them as a monkey tool to clean up tenons.

Of course, you can also make a stand for it to get it up off the floor. I've seen some pretty nice stands. Some allow the block to sit flat for using the through-holes while having a slot in the middle so you can stand the thing on edge when using the swages.

I have one that's similar, but I don't have a lot of room, so it is slid under a bench, standing up, and only gets pulled out when I need it. Which isn't very often.

Pete Stanaitis
---------------
Reply With Quote
The Following 2 Users Say Thank You to Pete Spaco For This Post:
  #5  
Old 05-29-2019, 10:38:13 PM
Kevin O. Pulver Kevin O. Pulver is online now
Email NOT Working
 
Join Date: Nov 2004
Location: Kenesaw, Nebraska USA
Posts: 4,256
Thanks: 1,195
Thanked 1,962 Times in 1,200 Posts
Default Re: Swage Block

I love my glass beading cabinet but I hate a new finish on Old Iron.
I agree with Tracy and would go for the knotted wire cup brush on an angle grinder. A little oil rubbed on next.
Reply With Quote
The Following User Says Thank You to Kevin O. Pulver For This Post:
  #6  
Old 05-30-2019, 10:53:51 AM
Bob Willman Bob Willman is offline
Registered
 
Join Date: Sep 2009
Location: Bowling Green, Ohio
Posts: 433
Thanks: 1
Thanked 271 Times in 173 Posts
Default Re: Swage Block

I have one very similar in my blacksmith shop. If you keep it inside, I would wire brush it and leave it alone. I built a stand for mine using a wooden utility pole set into the dirt floor of the shop. There is a notch equal to the thickness of the block cut into the top of the pole several inches deep. The block can be laid on top flat or set on edge in the notch so that the desired edge is on top.

Bob
WB8NQW
Reply With Quote
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
How to Make Anvil and Swage Block from sheet metal Pete Spaco Blacksmithing and Metallurgy 0 11-26-2011 01:58:27 AM
New Guy on the Block MahleCleviteVRGaskets Smokstak Forums Meet and Greet 5 10-06-2011 07:34:58 AM
New guy on the block; pics of 67 12.5 RJC dieselride Onan Generators 12 04-24-2009 01:45:36 PM
f\m block Donnie Devore Sr. Hit & Miss Gas Engine Discussion 0 08-11-2006 07:01:18 PM
Salt block D Dcarpent Hit & Miss Gas Engine Discussion 2 06-28-2006 07:30:59 AM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 08:59:05 AM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2019 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277