Antique Engines and Old Iron
[Home] - [HELP] - [Forums] - [Library] - [Photo Gallery] - [Groups] - [Classified Ads] - [Subscribe] - [Links] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® Antique Engine Community > Hit & Miss Gas Engine Discussion
Forgot Password? Join Us!

Notices

Hit & Miss Gas Engine Discussion Meet collectors of hit and miss engines, ask questions about collecting, restoring and showing antique flywheel engines.

Hit & Miss Gas Engine Discussion

Polished brass:To coat or not to coat?


this thread has 5 replies and has been viewed 7779 times

Closed Thread
 
Thread Tools Display Modes
  #1  
Old 01-03-2005, 03:49:29 PM
Lou Quirch Lou Quirch is offline
Subscriber
 
Join Date: Nov 2004
Location: Tavernier, Florida
Posts: 422
Thanks: 452
Thanked 125 Times in 62 Posts
Default Polished brass:To coat or not to coat?

I have spent a lot of time polishing the brass pipes on my engine and would like some imput on the pros and cons of coating the brass with clear laquer or something similar.
I finished the polishing yesterday and it already has water marks. Am I being too finicky or do others like shiny brass parts also. Much rather spend time running the engines than polishing them.


Thanks,
Lou
Sponsored Links
  #2  
Old 01-03-2005, 04:38:10 PM
Jeff Smith Jeff Smith is offline
Subscriber
 
Join Date: Nov 2004
Location: Port St. Lucie, Florida, USA
Posts: 3,961
Thanks: 4,124
Thanked 2,668 Times in 1,065 Posts
Default Re: Polished brass:To coat or not to coat?

I like the brass to shine. I polish stuff on the buffing wheel with compound and then finish by hand with semi-chrome or a similar brass cleaner/polish that leaves a coating on it like Flitz (Eastwood). I have tried to coat stuff with clear coatings, but then I had to clean that off later to polish it again.

Jeff Smith
  #3  
Old 01-03-2005, 04:58:56 PM
Joe Morris Joe Morris is offline
Registered-III
 
Join Date: Nov 2004
Location: Powell Tn.
Posts: 814
Thanks: 5
Thanked 131 Times in 98 Posts
Default Re: Polished brass:To coat or not to coat?

The best thing I have ever found to keep brass or copper shining after buffing is to coat it with Johnsons paste floor wax. It kept a copper washing machine shining for years. Before that I could polish it and the next day it would be tanished again. It's worth a try.
Joe Morris, Good luck in a good hobby.
  #4  
Old 01-03-2005, 04:59:53 PM
Chris Curtis
Guest
 
Posts: n/a
Default Re: Polished brass:To coat or not to coat?

I like to keep my stuff polished to a high shine. I have tried to coat stuff before with poor results and do not recommend it. First of all brass that is coated will not shine as well as just polished. Second if the coating is damaged by fuel, heat or scratched the brass will tarnish in those spots and trying to polish it and repair the coating is impossible as the whole thing will become blotchy, then you will have to strip it and start over which is much harder then just keeping up on the polishing. I use Never Dull wadding and have found that if I polish frequently and never let the tarnish get bad then it is only a few minute job at every show to make it look good.
  #5  
Old 01-03-2005, 05:29:15 PM
BWegher BWegher is offline
Registered-III
 
Join Date: Nov 2004
Location: McCook, Nebraska USA
Posts: 533
Thanks: 0
Thanked 34 Times in 31 Posts
Default Re: Polished brass:To coat or not to coat?

A very highly polished surface will corrode more slowly. First buff with white rouge to get mirror finish. Then maintain with red rouge or tripoli.
  #6  
Old 01-03-2005, 08:11:36 PM
Jim Tremble Jim Tremble is online now
Subscriber
 
Join Date: Nov 2004
Location: Washington
Posts: 1,924
Thanks: 4,867
Thanked 738 Times in 373 Posts
Default Re: Polished brass:To coat or not to coat?

On my brass parts, I use Mothers Alumium Polish. It does a fantastic job. No mess and little effort. With this, I can shine a part in less that 3 mins.

Try it,

Jim
Closed Thread

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
Coat Hangers as Welding Rod Beanscoot Welding Shop 38 02-26-2016 01:00:13 AM
Powder Coat 95gts Garden Tractors and Mowers 16 10-22-2012 11:19:02 PM
What to use to coat water jacket? vern0n Hit & Miss Gas Engine Discussion 6 12-08-2008 11:32:20 AM
Clear coat John Bunting Paint Shop 1 01-26-2004 06:00:13 PM
Clear Coat? Ron Paint Shop 2 06-09-2002 09:43:14 PM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 12:15:09 PM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2019 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277