Antique Engines and Old Iron
[Home] - [HELP] - [Forums] - [Groups] - [Classified Ads] - [Subscribe] - [Books] - [Sponsors] -

Go Back   SmokStak > SmokStak® Antique Engine Community > Small Air Cooled Gasoline Engines > Garden Tractors and Mowers
Forgot Password? Join Us!

Notices

Garden Tractors and Mowers Vintage lawn and garden tractors, mowers, snow blowers, snowmobiles and other old machinery that is driven by small air cooled engines.

Garden Tractors and Mowers

Sears ST12 Tecumseh Starter Difficulty Mystery and Carburetor Blow Back


this thread has 61 replies and has been viewed 2419 times

Reply
 
Thread Tools Display Modes
  #61  
Old 07-20-2019, 10:00:08 PM
Glenn Ayers Glenn Ayers is offline
Subscriber
 
Join Date: Oct 2005
Location: Bethany, West Virginia, USA
Posts: 1,784
Thanks: 2,121
Thanked 2,189 Times in 876 Posts
Default Re: Sears ST12 Tecumseh Starter Difficulty Mystery and Carburetor Blow Back

Have ya tried a bigger .. better battery ?

.
__________________
"I'll have the Red Pill, thank you."
Reply With Quote
Sponsored Links
  #62  
Old 07-20-2019, 11:20:02 PM
Mark Abner Mark Abner is offline
Subscriber
 
Join Date: Jun 2009
Location: Louisville, Kentucky, USA
Posts: 58
Thanks: 14
Thanked 37 Times in 16 Posts
Default Re: Sears ST12 Tecumseh Starter Difficulty Mystery and Carburetor Blow Back

Been reading along, I have restored many Tecumseh HH120 engines for suburban tractors so here is my opinion, go back to engine basics, starter stall on compression will not cause excessive fuel to blow out the carb or flood the cylinder just like faulty carb will not cause starter stall. Don't confuse ignition timing with valve timing. Ignition timing fires the plug at the proper time in relation to number of degrees of crankshaft rotation, valve timing operates intake and exhaust valves in relation to piston location. every HH120 I have done the flywheel was a bear to remove, since yours came off easy I bet someone has been in the engine. It sounds to me like your cam timing is off. Remove the side cover of the engine, you will see a punch dot on the crank gear and a punch dot on the cam gear, rotate the crank and make sure these two dots line up at some point. This way you will know for sure your cam is set correctly. Put the side cover back on, next release the valve springs and pull the intake and exhaust valves inspect the seats then lap the valves for a perfect seal. This way you know exactly that the valve timing is set correct and the valves are seating on fresh seats.
Reply With Quote
The Following User Says Thank You to Mark Abner For This Post:
Reply

Bookmarks


Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

F o r u m Jump

Similar Threads Chosen at Random
Thread Thread Starter F o r u m Replies Last Post
Cylinder oiler blow back problems boz Scale Model Engineering 2 09-08-2012 08:34:53 PM
Sears ST12 tractor Tecumesh engine richie25rich Garden Tractors and Mowers 3 04-10-2008 10:20:04 AM
Oiler pipe blow back Jesse Zilafro Hit & Miss Gas Engine Discussion 6 02-16-2007 12:26:25 PM
3 hp Mc Cormick M blow back in oiler? Lenn Antique Engine Archives 5 02-17-2004 10:24:19 PM
Oiler blow back! fixing the problem!! Adam Cottrill Antique Engine Archives 21 02-07-2002 02:00:25 AM


Use "Ctrl" mouse wheel to change screen size.
All times are GMT -4. The time now is 03:44:19 AM.

Smokstak and Enginads site search!


All use is subject to our TERMS OF SERVICE
SMOKSTAK® is a Registered Trade Mark - A Community of Antique Engine Enthusiasts
Copyright © 2000 - 2019 by Harry Matthews P.O. Box 5612 - Sarasota, FL 34277